深圳億博檢測CE認證機構致力于產品質量檢測,CE認證,3C認證等各類檢測認證服務。
歡迎撥打檢測熱線 135-4327-2595
掃碼咨詢

深圳億博檢測機構(EBOTEST)

135-4327-2595

掃碼咨詢

ASTM D 2134 ASTM D2134 - 93(2007) Sward-Type Hardness of Org

瀏覽次數: | 2011-02-22 11:43

億博CE認證機構一個專業全面的、經驗豐富的認證服務機構,已有超過十年的檢測認證經驗,擁有資深技術團隊為您提供全方位檢測認證需求,服務熱線:135-4327-2595


ASTM D2134 - 93(2007)
Standard Test Method for Determining the Hardness of Organic Coatings with a Sward-Type Hardness Rocker 有機涂層斯華德硬度測試方法
Significance and Use
Sward-type hardness rocker instruments have been used by the coatings industry for more than a half a century as a nondestructive test instrument to measure cure and ultimate surface hardness of organic coatings (see Refs. (1) through (11)). An accepted standard test method for the use of such an instrument is long overdue.
In previous task group work designed to establish an ASTM method for measuring hardness of organic coatings with Sward-type hardness rocker instruments, round-robin test results continually showed poor interlaboratory reproducibility. This lack of interlaboratory agreement could have resulted from dimensional variations among instruments, with the contact rocker rings as the most likely offender in that regard. There are several producers of Sward-type hardness rockers making instruments that differ among themselves in net weight and ring radius. Some of them exceed the measurements and net weight called for in this test method.
This test method, however, is useful within laboratories to quickly screen and measure the surface hardness of candidate coatings.
1. Scope
1.1 This test method covers the determination of the relative degree of surface hardness of organic coatings using a specific apparatus widely used in the coatings industry.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This test method does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents
ASTM Standards
D823 Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D3924 Specification for Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials
D4138 Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means

Index Terms
hardness; hardness tests—Sward hardness; surface hardness; Hardness tests--organic coatings; Organic coatings; Surface hardening/hardness; Sward hardness rocker; ICS Number Code 25.220.60 (Organic coatings)
有機涂層的Sward hardness (斯華德硬度測試)是以水平測試板上的滑輪震蕩次數作為基準,以玻璃板的震蕩次數作為100%,其他結果以百分比的形式表示,具體測試詳情如下:
METHOD OF USE
The levelling table with the test plates is levelled carefully and the surface of the glass test plate thoroughly cleaned. The underside rings of the rocker should be examined critically and cleaned with a suitable solvent to remove any sticky deposits.
1. Place the rocker carefully into the test surface, roll the instrument to the right until
bubbles are in view.
IMPORTANT: ensure that NO undue pressure is applied to the rocker.
2. Release the rocker START counting the number of ‘rocks’ (complete oscillations)
when the LEFT-HAND bubbles just disappears.
3. STOP the count when the right-hand bubble just disappears.
The rocker is set before despatch to make 50 oscillations on a standard glass plate with the period of oscillation being set at 60+0.5 seconds by means of the adjustable knurled nuts. A frequent check should be made on the number of oscillations the apparatus makes on the standard glass plate.
It is usual to express the results obtained from the test piece as a percentage of the number of rocks made on the plate glass standard representing 100%.
The change of state for rocker hardness can be monitored against time provided that the coating is smooth, free from blemishes, and its thickness controlled.
Sample Requirement :6*6inches ,4PCS.

有產品辦理檢測認證或想了解更多詳情資訊,請聯系億博檢測中心!

億博檢測高級銷售顧問certified engineer

胡玲

胡玲 2012年進入億博檢測技術有限公司,擔任高級銷售顧問。
精通各類檢測認證標準,服務過上千家企業。 聯系方式:13543272595(微信同號) 座機:0755-29413628
郵箱:huling@ebotek.cn
地址:深圳市寶安新安六路勤業商務中心A棟一樓112-114
掃一掃加工程師微信    掃一掃加工程師微信

本文連接:http://m.yjcig.cn/hxjc/en71jc/4426.html



相關文章
  • 常用美國ASTM紡織品330個標準(下)



  • 此文關鍵詞:,the,of,hardness,and,for,to,te